Dewalt dws780 manual

Looking for:

- DeWalt Miter Saw Owner's Manuals - Mike's Tools

- DEWALT DWS INSTRUCTION MANUAL Pdf Download | ManualsLib

These can deflect and contact the guard, and can cause damage to the machine. A cracked or damaged. Cleaning the blade and. A cracked. The polycarbonate material used in the guard is subject to attack by certain chemicals. Clogged motor air slots can cause. Clamp all workpieces that would cause your hand to be within 6" mm of the saw blade. Severe personal injury may result.

Always make a dry run. Information is also available from the National. Please refer to the American. Do not connect unit to electrical power source until complete instructions are read. Previous Page. Next Page. Make sure the miter saw is placed on a secure supporting surface and does not The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme, slip or move during use. Page 2: Optional Accessories The switch is susceptible to failure if direct current is used.

A voltage decrease of 10 percent or more will cause a loss of power and overheating. If this tool does not operate, check the power supply. Page 4: Features And Controls If a delay or "skipping" occurs, turn the saw on and off 4 or 5 times.

Always be sure the blade has stopped before removing it from the kerf. Page 5: Adjustments Use the material clamp provided with your saw. Other aids such as spring clamps, bar clamps or C-clamps may be appropriate for certain sizes and shapes of material. Use care in selecting and placing these clamps. Take time to make a dry run before making the cut.

Page 6: Special Cuts Position the material so that you will be cutting the thinnest cross section, DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any time as shown in Figure Figure 20 illustrates the wrong way to cut these extrusions. Saw not plugged in Plug in saw. Fuse blown or circuit breaker tripped 2. Replace fuse or reset circuit breaker. T ools built. As a result, your tool is equipped. NOTE: Double insulation does not take the place of normal safety precautions when operating this.

The secondary insulation system is for protection against injury r esulting from a possible failur e. Repair or. Polarized plugs one blade is wider than the other are used on equipment to r educe the risk of. When provided, this plug will fit in the polarized outlet only one way. If the plug does.

If it still does not fit, contact a qualified electrician to install. Do not change the plug in any way. Multi-V belt Roller bearings. Automatic electric brake Carbide blade. Safety Instructions for All T ools.

Form habit of checking to see that keys. T ools, scrap pieces,. Cluttered areas and benches invite accidents. The use of power tools. Keep your work area well-lit. All visitors should be kept at a safe distance from work area. Y our. The unauthorized start-up of a machine by a child or visitor may result in injury.

It will do the job better and be safer at the rate for which it was. Using the incorrect tool or attachment may result in personal injury. Do not wear loose clothing, gloves, neckties, rings, bracelets, or. Nonslip footwear is recommended. Everyday eyeglasses are NOT safety glasses. Use clamps or a vise to hold the workpiece on the table and. It is safer than using your hand and it frees both hands to operate tool. Keep proper footing and balance at all times.

Loss of balance may. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. Poorly maintained tools and. An accidental start-up can cause injury. Do not touch the. Make sure that the switch is in the. How do you open the mitre saw. What is crosscut positioning system?

What is the best way to clean my saw blade? Wipe sawdust from the saw blade with a brush. Spray the saw blade with oven cleaner and leave for 30 minutes. Remove the oven cleaner and dirt with a dry cloth. Grease saw blade with Vaseline. My saw blade is blunt.

What now? If there is resin or other debris on the blade, it may look like the blade is blunt. P, Q Ensure that the material does not move or creep while cutting; clamp it securely in place.

Always To best understand how to make the items listed here, we suggest that you try a few simple let the blade come to a full stop before raising arm. Bevel left Bevel right Miter table set at right Miter table set at left Page Maintenance Fig.

This is extremely important when making angle cuts. Page Specifications 3.